Ashtech Z-sensor Manuel d'instructions Page 135
- Page / 190
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Command Response Formats Page 119
Command
$PASHR,UTM
The response message is in the form $PASHR,UTM,.... as shown below.
Example:
For RTCM Differential:
$PASHR,UTM,015454.00,10S,588757.62,4136720.05,2,04,03.8,+00012,M,,M14,1010
For CPD Differential (RZ Only):
$PASHR,UTM,015454.00,10S,588757.62,4136720.05,2,04,03.8,+00012,M,,M14.123,1010
NMEA VTG (Velocity/Course) Message
$PASHS,NME,VTG
This command enables/disables the velocity/course message. The structure is
$PASHS,NME,VTG,x,y
where x is the output port A, B, or C and y is ON or OFF. This message is not output
unless position is computed.
Example: Enable VTG message or port B
$PASHS,NME,VTG,B,ON followed by output command
$PASHS,OUT,x,NMEA where x is the output port.
$GPVTG
The response is a message in the form:
eeeeeee.ee East UTM coordinate 0 through 9999999.99 meters
nnnnnnn.nn North UTM coordinate 0 through 9999999.99 meters
q GPS quality indicator
1 = GPS available
2 = RTCM differential available
3 = Carrier phase differential (CPD) available
ss Number of satellites being used 3 through 12
hh.h HDOP 0 through 99.9
aaaaa Antenna height in meters -1000 through 18000
ggg.g Geoidal height in meters -999.9 through 999.9
aa Age of data link differential data 0 through 99 seconds
l.lll RZ only - solution latency in CPD rover mode. 0.0 through 0.999
milliseconds. Stays at 0.999 if latency is greater than 0.999.
ssss Differential reference station ID 4-character string
Table 4.69: NMEA UTM Structure (continued)
Field Description
- Z-12 Real-Time Sensor 1
- Operation & Reference 1
- Table of Contents 5
- List of Figures 11
- List of Tables 13
- Introduction 17
- Functional Description 18
- Real-Time Differential 19
- Equipment 20
- Specifications and Options 21
- Memory Options 22
- Operation 23
- Front Panel 24
- RF Connector 25
- Power Input Connections 26
- Serial Port Configuration 27
- Serial Null Modem Data Cable 29
- Default Parameters 29
- Getting Started 30
- Powering On the Sensor 31
- Receiver Memory Reset 32
- Communication with the Sensor 32
- Monitoring Satellite Tracking 33
- Monitoring Position 33
- Command Response Formats 34
- Differential Setup 35
- Hardware Setup 36
- CPD with DBEN message 37
- RTCM Differential Setup 39
- Base Setup 41
- Rover/Remote Setup 42
- Understanding CPD 47
- Solution Latency 48
- Data Link Monitor 48
- Real-time Solution Output 48
- Vector Solution Output 49
- Solution Storage 50
- Troubleshooting 51
- CPD Solution Parameters 53
- Dynamics: $PASHS,CPD,DYN 54
- Multipath: $PASHS,CPD,MTP 55
- Rate: $PASHS,CPD,PER 55
- Fast CPD: $PASHS,CPD,FST 55
- Universal RTCM Base Station 56
- Understanding 57
- Table 4.1: Command Summary 60
- General Sensor Commands 66
- Set Antenna Height 69
- Set Antenna Offsets 69
- Query Antenna Parameters 70
- Query Sensor Configuration 71
- Store String 72
- Query File Directory 72
- Set Elevation Mask 74
- Close or Delete File 74
- Set Altitude-Fixed Mode 75
- Request File Information 75
- Set HDOP Mask 77
- Select Ionospheric Model 78
- Query Ionospheric Data 78
- Set Photogrammetry Edge 81
- $PASHS,PHE,x 81
- Set Minimum Satellites 81
- Set PDOP Mask 82
- Set Position Elevation Mask 82
- Log Project Data 82
- Set Position Mode 83
- Set Position of the Antenna 83
- Query Port and Baud Rate 85
- Set Receiver To Sleep Mode 85
- Set Recording Interval 86
- Query Radio Mode Parameters 86
- Turn Data Recording On/Off 87
- Query Sensor (Receiver) ID 87
- Set Type of Data 88
- Upload Route Information 93
- Save Parameters 93
- Enter Site ID 94
- Set Communication Baud Rate 94
- Query SV Mode Selection 96
- Use Unheathy SVs 96
- Designate Satellites to Use 97
- Set VDOP Mask 97
- Query Week Number 97
- Upload Waypoint to Sensor 97
- Set Sensor to Z Mode 98
- Raw Data Commands 99
- Query CBEN Message 100
- Query Vector Solution 101
- Command 103
- Query PBEN Data for One Epoch 104
- Query Raw Data Parameters 105
- Query UBN Message 106
- NMEA Data Message Commands 109
- Disable All NMEA Messages 111
- NMEA Almanac 111
- Autopilot Message 112
- NMEA Bearing and Distance 113
- NMEA Decimal Almanac Message 114
- GGA (GPS Position) Message 115
- GLL (Latitude,Longitude) 117
- NMEA MSG (RTCM) Message 125
- Set NMEA Send Interval 130
- NMEA Message VTG (COG/SOG) 137
- NMEA Cross-Track Error 137
- RTCM Commands 138
- Initialize RTCM Setup 140
- Define RTCM Message 141
- Disable Differential Mode 141
- Set Quality Threshold 141
- Check Sequence Number 142
- Set RTCM Bit Rate 142
- Set Station Identification 142
- Enable Type of Message 143
- CPD Commands 147
- OR $PASHS,BPS,ANT 148
- Query Data Link Status 149
- Set Rover Dynamics 150
- Set Current Raw Position 151
- Enable/Disable Fast CPD Mode 152
- Display CPD SV Information 152
- CPD Mode Select 153
- Select CPD processing cycle 155
- Set Multipath Parameters 155
- Select Solution to Output 155
- Set CPD Update Interval 156
- Set BPD Transmission Period 156
- Set DBEN Transmission Period 157
- Reset CPD Processing 158
- CPD Status 159
- Query CPD Solution Status 161
- Select Base Position - Rover 161
- Display Station Coordinates 162
- Field Description 163
- Packed DBEN 165
- Report Real-Time Error 167
- Photogram 169
- Radio Link 171
- Sensitivity 172
- Differential GPS 173
- Sources of Error 175
- Data Link Related Errors 176
- Differential Message 177
- Glossary 179
- Numerics 185
Produits connexes et manuels pour Navigateurs Ashtech Z-sensor
(58 pages)Kenmore 5.7 cu. ft. Electric Range w/ True Convection - Bisque manuales
Manuales del propietario y guías del usuario para Cocinas Kenmore 5.7 cu. ft. Electric Range w/ True Convection - Bisque.
Ofrecemos 1 manuales en pdf Kenmore 5.7 cu. ft. Electric Range w/ True Convection - Bisque para descargar gratis por tipos de documentos: El manual del propietario
Commentaires sur ces manuels